Gebraucht SVG 86-3 #117943 zu verkaufen

SVG 86-3
Hersteller
SVG
Modell
86-3
ID: 117943
Wafergröße: 3"
single cabinet developer system, 3" Configuration: Wafers: 3" round Silicon wafers, convertible up to 6" with kit option Process flow: left to right Track 1: send, bake, chill, MD develop, bake, chill, with flood expose, receive Track 2: send, HMDS vapor prime, chill, coat, bake, bake, chill, receive System specifications: Frame: Internal frame: standard powder coated black External panels: stainless steel System: Emergency stop access in front of system Rear system bulkhead fittings and facility connections: Process chemicals: EBR solvents, developer, DI water Process gasses: clean dry air, Nitrogen Process exhaust Cooling water System transport: O-ring belt transfer Polyurethane Silicone Viton Serial processing Indexer module: Platform designed for SEMI standard 3" wafer cassettes Hard anodized aluminum Standard 3" SEMI standard cassette pitch indexing Capable of handling up to 6" SEMI standard wafer cassettes Photoresist coat module: Arc centering configured for 3" round silicon wafers Brushless motor: 1 RPM spin speed programmability up to 6,000 RPM Programmable pivoting moving dispense arm: (1) Photoresist nozzle (3) Topside EBR TEFLON catch cup with built-in backside EBR Pre-dispense cup with programmable pre-dispense Digital vacuum switch Interlocked safety cover to stop process when removed Center collection 1 gallon polyethylene drain container, high level sensor 5-gallon SS canister with low level sensing for EBR solvent dispense Positive resist moving dispense developer module (aqueous) Arc centering configured for 3" round silicon wafers Brushless motor: 1 RPM spin speed programmability up to 6,000 RPM Programmable pivoting moving dispense arm: (1) 1/4” O.D. developer nozzle (1) 1/4” O.D. DI water rinse nozzle (1) SS11001 developer spray nozzle (1) SS11001 DI water rinse nozzle Polyethylene catch cup with built-in arm home positioning off wafer Digital vacuum switch Interlocked safety cover to stop process when removed 2" Polyethylene drain to rear of system for facility connection 5-gallon SS canister with low level sensing for aqueous developer Chill plate module: Hard anodized aluminum surface Internal water channels for high efficiency heat transfer 3/8" Swagelok tubing input and output connections Hotplate oven module: Hard anodized Aluminum 3-pin HPO block assembly 3-pin stepper motor programmable wafer lift handling Enhanced heating element (Std. 120V, 450W) Optional enhanced heating element (High Temp. 120V, 750W) WATLOW temperature controller Auto tuning +/- 0.1% calibration accuracy Temperature range: 50ºC to 250ºC (Standard) Temperature range: 80ºC to 350ºC (High Temp.) Temperature uniformity: +/- 0.5ºC (at 100 ºC) Digital LED display Temperature readout to 0.1ºC RTD temperature probe Digital vacuum switch NetTRACK system manager: NetTRACK CPU board Industrial PC Multitasking Windowsxp application software HCIU card cage connection port NetTRACK system management software Recipe management Unlimited recipe writing Easy editing and copying Component exercise Real-time display of process set points Real-time processing data logging Four access security levels with password control Seamless integration with production server Configurable for all process steps SECS-GEM compliant ports print out in MS Excel format 15” ELO color touch-screen, 1024 x 768 resolution at 75 Hz Ergotron monitor arm, (angles and height adjustable, SEMI compliant) Emergency stop button front Main breaker on power distribution box Barcode reader Flood exposure: Configured for 3" wafers (4" shutter opening) Lamp: 350W Wavelength: 365 nm Intensity range: 18mW to 24mW Module mounted on developer chill plate Exposure interface board to system software control Facilities requirements: Power (system): 208V, 3-phase, 60Hz, 5-wire, 35A Power (chiller): 120V, 1-phase, 60Hz, 3-wire, 15A Vacuum: 5 SCFM at 28" Hg, 3/8" OD tube Gas (CDA): 70 to 100 psig, 10 SCFM per system, 1/4" OD tube Gas (N2): 80 to 100 psig, 10 SCFM per system, 3/8" OD tube Process exhaust (coater/developer): 35 SCFM at 1.5" H2O/module, 4" duct Process exhaust (HPO): 10 SCFM at 1.5" H2O/module, 4" OD duct Cabinet exhaust (optional): 150 SCFM at 1.5" H2O, 4" OD duct Facilities connections: back of system System transport and installation: Transport: 4 wheels Securing: screw type mounting feet with pads Dimensions (W x D x H): 108 x 40 x 48" Options available for an additional cost: (Qty 4) IntelliGen Mini Photoresist dispense systems: 2-Stage Steppor motor technology and diaphragm design Filter Mounting bracked Interface cables (Qty 2) IntelliGen HV Photoresist dispense systems: 2-Stage Steppor motor technology and diaphragm design Filter Mounting bracked Interface cables (Qty 4) 451-15-1-S IDS 1/4 x 1/4 units with suckback valves: Bushings and compression nuts for input and output connections (1) output 0 to 15 PSI pressure For resist (0-80cp), Barli, and ARC (0-80cp) Power supply Interface cables Software (Qty 2) CYBOR 7500 precision chemical dispense pumps: Mid-range viscosity: 300 cp to 3000 cp 3/8" Flare-type connections KALREX O-rings Variable rate dispense High-torque stepper motor control Dispense volume: maximum 16ml Programmable suckback Multiple recipe select On-board single-pump controls RS232, RS485, LON communications Power supply Interface cables Software Chill plate closed loop temperature control unit: Connection tubing Can be shared with more than one chill plate Developer temperature control unit: Closed loop recirculation heater / chiller Manifold and connection tubing to dispense arm Single temperature delivered to dispense arm Electro-polished 5-gallon SS solvent canisters, low-level sensing Dual chemistry developer dispense system.
SVG 86-3 ist eine positive Photolackausrüstung, die zur Erzeugung hochwertiger, hochauflösender Muster auf Leiterplatten verwendet wird. Es handelt sich um ein Einkomponentensystem, bestehend aus einem flüssigen Photoresist und einem Katalysator, die in separaten Behältern gelagert werden. Der Photoresist ist ein Diazonaphthochinon (DNQ) -Typ Novolak, während das Katalysatormittel ein Katalysator auf Aminbasis ist. Bei Bestrahlung mit UV oder anderen Strahlungsformen durchläuft 86-3 flüssige Photoresist eine radikalische Kopplungsreaktion mit dem Katalysator, die schließlich eine dreidimensionale Polymerstruktur bildet. Das Polymer ist in vielen gängigen Lösungsmitteln unlöslich und sehr resistent gegen chemische und Ätzprozesse. Dies ergibt ein Muster mit sehr feiner Auflösung und macht SVG 86-3 Einheit ideal für den Einsatz in Mikrofabrikation und Feinabstand, qualitativ hochwertige Fertigungsprozesse. 86-3 Photolackmaschine kann direkt auf eine Vielzahl von Substraten wie Kupfer, Aluminium, Glas, Keramik und Silizium aufgebracht werden. Einmal belichtet, kann der Photoresist mit einer Vielzahl von Ätzmitteln wie Eisenchlorid oder Kaliumpermanganat entwickelt und geätzt werden. Nach diesem Ätzvorgang verbleibt das gewünschte Muster auf dem Substrat und der ungehärtete Photoresist kann in Wasser oder einem geeigneten Lösungsmittel weggewaschen werden. SVG 86-3 Photoresist-Tool wird häufig in der Herstellung von Halbleiterbauelementen, Leiterplatten und Sonden sowie im Laserdesign, in Anwendungen für medizinische Geräte und in der medizinischen Diagnostik verwendet. Die hochauflösende Bildbildung und die chemische Beständigkeit des resultierenden Polymers machen 86-3 Asset zu einem der besten und vielseitigsten positiven Photoresists, die zur Verfügung stehen.
Es liegen noch keine Bewertungen vor